F30 CK Centreboard movement

Engines, Drive trains, Propellers, Steering, Ground Tackle and other mechanical system

F30 CK Centreboard movement

Postby AndyLamble » Sun Aug 25, 2019 5:49 pm

I own Tusitala (ex Freedom Freya) a F30 CK built by Fairways Marine in 1980. I have found that it is easy to rock the CB from side to side when it is in the raised position and on blocks (the boat is out of the water). I can move the trailing edge about 40mm from side to side by pushing sideways at the lifting tackle attachment point. What level of play is typical and/or to be aimed at when the bearing and pivot have been refurbished?

Andy
F30 CK Tusitala
AndyLamble
 
Posts: 2
Joined: Mon Nov 06, 2017 6:31 am

Re: F30 CK Centreboard movement

Postby Castaway » Mon Aug 26, 2019 8:45 am

I replaced the bearing and, later, the rubbing pads on Castaway's centreboard, but it still moves, and bangs about in a seaway, just as it has done since we bought her. If you find a way to stop it, please let me know.

On the plus side, it's no worse after another ten years, and the boat continues to sail as well as ever. On the UK F35, the shape of the slot in the bottom of the boat matches the lowered CB quite closely, and that prevents any significant rotation of the board, which would be bad. Any lateral tilt is minimal and can have no effect. I expect the F30 is similar.

Replacing the bearing is quite a task; you have to be able to lift the front of the CB about 6", remove a pin at the top of the casing, then lower it all 6" below the keel to reach the pin and sleeve. Unlike the F40, the pin does not go through the hull, but is held in a yoke which slides up and down. On the F35, that is also held in place by bolts through the CB case above the waterline.

One other caveat; if you replace the pennant lifting the board, don't use thicker line than 10mm, because it binds on the sheaves and makes raising more difficult. 8mm Dyneema or the like might be better.

Regards,

Gerald
Gerald Freshwater,
s/y 'Castaway', (UK F35 cat ketch, centreboard, 1987)
Lerwick Boating Club
Shetland Isles, Scotland
User avatar
Castaway
 
Posts: 199
Joined: Sat Dec 13, 2008 8:40 pm
Location: Lerwick, Shetland Isles

Re: F30 CK Centreboard movement

Postby AndyLamble » Mon Aug 26, 2019 5:18 pm

Gerald,

Thanks for your reply, my gut feeling is to leave it and monitor for any deterioration. The F30 doesn't seem to have any rubbing pads but as you say the CB case is quite closely shaped to match the lowered CB. I am considering putting in an illuminated inspection window in the CB case top so I can see what is going on as well as worry about the noise from any slamming... The original lifting tackle had 14mm polyester braid on braid and a 3:1 purchase which seemed to not run freely and was too heavy to winch easily so I have put in a 6:1 system and dropped to 10mm line. Another improvement will be to put a pin through the CB case and the CB lifting pennant attachment so that I can lock the CB in the raised position and relax the load on the pennant when she is at her mooring.

Andy
F30 CK Tusitala
AndyLamble
 
Posts: 2
Joined: Mon Nov 06, 2017 6:31 am

Re: F30 CK Centreboard movement

Postby Castaway » Mon Aug 26, 2019 7:15 pm

Andy,

Be sure you can waterproof the pin mounting holes; the water sloshes back and forth in the CB casing in a seaway. I often hear the huffing sound of air blowing through the pipe carrying the pennant up to the deck as the boat pitches slightly.

The inspection window sounds useful. We keep so much stuff on the top of the case, it would rarely be visible. Again, waterproofing will be vital, especially since spillage at this point collects under the floor boards instead of draining straight into the bilge.

Gerald
Gerald Freshwater,
s/y 'Castaway', (UK F35 cat ketch, centreboard, 1987)
Lerwick Boating Club
Shetland Isles, Scotland
User avatar
Castaway
 
Posts: 199
Joined: Sat Dec 13, 2008 8:40 pm
Location: Lerwick, Shetland Isles

Re: F30 CK Centreboard movement

Postby Goose13 » Sat Aug 31, 2019 2:26 pm

If it makes u feel better, my Center Board knocks in most sea states when it’s down. It takes a little while to get use to the noise while on passage. But I’ve never seen any damage to the trunk when I’ve had it pulled for a bottom job.
Doug and Marie
Millennnium Falcon F33 CK cb #4
1980 wish bone booms Electric Drive
Goose13
 
Posts: 71
Joined: Tue Aug 19, 2014 7:18 pm


Return to Engines and Mechanical Systems

Who is online

Users browsing this forum: No registered users and 3 guests

cron